Home > Technical Articles

Spring Probe Contact Resistance: Travel, Force and Why a Two-Wire Measurement Lies

2026-11-16

A spring probe is a mechanical spring, a sliding contact and a signal path in one component. When a fixture starts producing intermittent failures, the probe is usually blamed last and replaced first. A short measurement routine, done properly, tells you whether the probe is actually at fault.

Start with travel, not resistance

Every probe has a rated travel, and the contact force is specified at a point on that travel, usually two thirds of it. A fixture that compresses the probe to 40 % of travel runs at a fraction of the rated force. The result is a contact that looks fine on a static bench test and opens when the fixture frame flexes under load.

  • Measure the free length and the compressed length at the point of contact, not the nominal stack height.
  • Allow for board tolerance, plating thickness and fixture wear. A 0.2 mm stack-up error is normal and must be absorbed inside the working travel.
  • Check that the probe bottoming out is impossible; a fully compressed probe has no compliance left and transfers force into the barrel.

Choosing force for the target

Bare copper or gold padLight force is enough; the risk is pad damage rather than oxide penetration.
HASL or contaminated padHigher force and a crowned or serrated tip help break through the layer.
Fine pitch arrayForce per probe drops because the total force on the board is limited; check total load, not just single-probe force.
High-current pathUse a probe rated for the current and derate for multiple probes carrying current at the same time.

Why a two-wire ohmmeter misleads

Putting a handheld ohmmeter across a probe and a return path measures the probe plus the leads plus the return. On a 50 mOhm probe, 200 mOhm of lead and clip resistance dominates. The usable method is four-wire: force current through the probe and the return, and measure voltage at the probe tip and at the return point with separate sense leads.

Two practical details decide whether the number means anything:

  1. Keep the open-circuit voltage low, around 20 mV or less, so that surface films are not artificially broken down during the measurement.
  2. Measure at the working travel and at the working current, or state clearly that the reading was taken at low current.

Reading the trend rather than the absolute value

A new probe may read 20 to 50 mOhm. What matters is the trend across a production run. A rise of a few milliohms over tens of thousands of cycles is normal bedding-in; a step change after cleaning is a sign that the plating has worn through. Keep a log per fixture position, not per probe batch, because the position tells you about alignment and the batch tells you about supplier consistency.

Wear signs that predict intermittents

  • Barrel wear at the plunger exit: a visible ring or a loose plunger. Side load from a misaligned fixture accelerates this.
  • Plating worn to base metal: a colour change at the tip, often copper-coloured under gold.
  • Contamination: flux residue carried in on the tip, which carbonises and raises resistance.
  • Spring set: free length shorter than a new probe, so the rated force is no longer reached at the same travel.

Cleaning with isopropyl alcohol and a lint-free swab recovers contamination, not wear. Replacing a single probe in an array without checking the neighbours usually moves the failure to the next weakest position.

A ten-minute fixture audit

Measure travel at four corners of the fixture, record four-wire resistance on ten representative probes, check total board load against the fixture specification, and inspect tips under magnification. That routine finds most intermittent-contact causes before a production lot does. The test probe and pin range lists force and travel options by series, and the plug and socket gauge range covers the mating-side checks.

CONTACT US

Contact: Eason Wang

Phone: +86-13751010017

Tel: +86-755-33168386

Email: info@iec-equipment.com

Add: 1F Junfeng Building, Gongle, Xixiang, Baoan District, Shenzhen, Guangdong, China

close
Scan the qr codeClose
the qr code