Home > Technical Articles

Probe Force and Contact Resistance: 0.5 N, 1 N, 2 N and Where the Curve Flattens

2026-11-16

Every spring probe datasheet quotes a force and a contact resistance, and the two numbers are usually printed in different columns with no relationship stated. In use they are tightly coupled: the force sets the real contact area, the real contact area sets the resistance, and the resistance sets whether a 30 mOhm limit means anything on a 20 mOhm part.

What contact resistance actually is

Measured resistance across a mated contact has three parts, and only the first is a property of the metal:

  • Constriction resistance. Current is forced through the small area where asperities actually touch. This dominates at low force.
  • Film resistance. Oxide, sulphide and plating interfaces sit between the metals. This dominates on aged contacts and on gold-flash over nickel.
  • Bulk resistance. The body of the pin, the barrel and the spring. Usually the smallest term and the easiest to calculate.

Constriction resistance falls roughly as the inverse square root of contact force, because the contact area grows with the deformation. That is the physics behind the curve everyone knows informally: doubling force does not halve resistance.

The shape of the curve

Applied forceTypical contact resistanceWhat is happening
0.3 N100 to 200 mOhmFew asperities in contact, films intact
0.5 N60 to 120 mOhmContact area growing quickly with force
1 N30 to 60 mOhmPlateau begins; films broken at asperity peaks
2 N20 to 40 mOhmLittle gain; wear rate rising
4 N15 to 30 mOhmPlateau; plating damage becomes the limit

The bands are typical rather than guaranteed, but the shape is reliable: between 1 N and 2 N most probes have already reached the part of the curve where force buys very little resistance. Going to 4 N buys a few more milliohms and costs a great deal of plating life.

The 2/3 travel rule and why it matters here

Spring probes are specified at a force measured at a stated deflection, usually two thirds of rated travel. A probe rated 1.2 N at 2/3 travel delivers roughly 0.8 N at 1/3 travel and about 1.5 N at full travel, because the spring is close to linear over its working range.

This means the force in a fixture is not the datasheet number unless the fixture plunges to the stated point. Two fixtures built to the same drawing can differ by 30 percent in contact force if one plunges 1 mm and the other 3 mm. The symptom is a resistance reading that is stable on one station and marginal on another, with the same probe part number.

  • Set plunge by a hard stop, not by air pressure or by feel.
  • Measure the stop with a height gauge after assembly; do not trust the CAD dimension.
  • Keep at least 0.5 mm of remaining travel so the spring is never bottomed out.
  • Check force with a load cell on a sample of stations, not on all of them.

Why the reading drifts upward over a shift

A probe that reads 25 mOhm at 08:00 and 60 mOhm at 16:00 has not changed its spring. The usual causes, in order:

  1. Debris on the tip. Flux, conformal coat and solder paste accumulate and act as a series film. The tip looks clean because the debris is transparent.
  2. Plating wear through. Gold flash over nickel wears at the crown points, exposing nickel, which oxidises. Resistance rises and becomes noisy.
  3. Barrel contamination. The plunger picks up contamination and carries it into the barrel, raising friction and reducing effective force.
  4. Thermal expansion of the fixture. A 5 K rise across a 200 mm aluminium fixture moves the stop by roughly 12 micrometres, which changes plunge and therefore force.

The second and third are cumulative and irreversible. This is why a 60 mOhm reading should be treated as a wear indicator, not a calibration problem.

What to measure and how

IEC 60512-2-1 defines the four-wire method for connector contact resistance, and it is the only defensible method for values in this range. A two-wire measurement adds the lead and contact resistance of the meter's own probes, which can easily be 30 to 80 mOhm — the same order as the value being measured. With four wires, the sense leads carry no current and the lead resistance cancels.

Two further rules keep the number honest:

  • Measure at the working current, not at 1 mA. Some films are non-ohmic and read low at low current.
  • Measure after the probe has been cycled at least three times. The first touch on an idle probe is always the worst reading of the day.

The test probe and test pin range lists probes by rated force at 2/3 travel; the catalogue indexes the barrels and receptacles that set the mechanical side of the same interface.

CONTACT US

Contact: Eason Wang

Phone: +86-13751010017

Tel: +86-755-33168386

Email: info@iec-equipment.com

Add: 1F Junfeng Building, Gongle, Xixiang, Baoan District, Shenzhen, Guangdong, China

close
Scan the qr codeClose
the qr code